Call Today

 

In this article in the next paragraph you can get lots of awesome points about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a bath tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a new one is additionally a moderately challenging project. If the old bathtub is readily accessible, the task can move easily; if you need to open a wall to remove the old bathtub as well as place the new tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the work and fit attempting it. Rather than employing a professional to take control of a halfway-completed task, it is better to take into consideration employing one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This article will certainly help you install a brand-new tub in your washroom if you have actually currently acquired a new tub and do not require to change the arrangement of your previous water supply pipelines.
Your devices and also material list should consist of the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Getting ready for the Installation

First of all, the sustaining framework provided with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final placement.

 

 

Removing Old Taps

If you need to change old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Installing the Tub

Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level reads level.
To set up taps, fit all-time low of the furthest adaptable faucet adapter to the suitable supply pipeline by making a compression join; then do the exact same for the various other tap.
Switch on the supply of water as well as check all joints and new pipework for leaks as well as tighten them if required. Fill up the bathtub as well as additionally inspect the overflow electrical outlet and the regular outlet for leakages.
Finally, fix the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the tub has actually been made use of at least when as this will certainly settle it into its final setting.

 

 

Suitable New Taps

If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washers are in location in between the faucet and the sink. Protect the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Tub

In the area where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a stiff seal, triggering the water to pass through the wall between the bathroom and also the tiling, leading to difficulties with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and also installations. They are sold in tubes and also cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealer can fracture relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the floor tiles using waterproof or waterproof adhesive and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

As a devoted person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that excerpt was smart. I beg you take a moment to share this blog posting if you liked it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .

Dial, and relax!